Juniper JN0-130인증시험도 어려울 뿐만 아니라 신청 또한 어렵습니다.Juniper JN0-130시험은 IT업계에서도 권위가 있고 직위가 있으신 분들이 응시할 수 있는 시험이라고 알고 있습니다. 우리 ITExamDump에서는Juniper JN0-130관련 학습가이드를 제동합니다. ITExamDump 는 우리만의IT전문가들이 만들어낸Juniper JN0-130관련 최신, 최고의 자료와 학습가이드를 준비하고 있습니다. 여러분의 편리하게Juniper JN0-130응시하는데 많은 도움이 될 것입니다.
ITExamDump에서 출시한 Juniper인증 JN0-130덤프는 실제시험문제 커버율이 높아 시험패스율이 가장 높습니다. Juniper인증 JN0-130시험을 통과하여 자격증을 취득하면 여러방면에서 도움이 됩니다. ITExamDump에서 출시한 Juniper인증 JN0-130덤프를 구매하여Juniper인증 JN0-130시험을 완벽하게 준비하지 않으실래요? ITExamDump의 실력을 증명해드릴게요.
시험 번호/코드: JN0-130
시험 이름: Juniper (Juniper networks Certified internet specialist.e(jncis-e))
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 128 문항
업데이트: 2014-03-02
이 글을 보시게 된다면Juniper인증 JN0-130시험패스를 꿈꾸고 있는 분이라고 믿습니다. Juniper인증 JN0-130시험공부를 아직 시작하지 않으셨다면 망설이지 마시고ITExamDump의Juniper인증 JN0-130덤프를 마련하여 공부를 시작해 보세요. 이렇게 착한 가격에 이정도 품질의 덤프자료는 찾기 힘들것입니다. ITExamDump의Juniper인증 JN0-130덤프는 고객님께서 Juniper인증 JN0-130시험을 패스하는 필수품입니다.
ITExamDump의 Juniper인증 JN0-130덤프를 구매하여 공부한지 일주일만에 바로 시험을 보았는데 고득점으로 시험을 패스했습니다.이는ITExamDump의 Juniper인증 JN0-130덤프를 구매한 분이 전해온 희소식입니다. 다른 자료 필요없이 단지 저희Juniper인증 JN0-130덤프로 이렇게 어려운 시험을 일주일만에 패스하고 자격증을 취득할수 있습니다.덤프가격도 다른 사이트보다 만만하여 부담없이 덤프마련이 가능합니다.구매전 무료샘플을 다운받아 보시면 믿음을 느낄것입니다.
Juniper인증 JN0-130시험을 어떻게 공부하면 패스할수 있을지 고민중이시면 근심걱정 버리시고ITExamDump 의 Juniper인증 JN0-130덤프로 가보세요. 문항수가 적고 적중율이 높은 세련된Juniper인증 JN0-130시험준비 공부자료는ITExamDump제품이 최고입니다.
성공을 위해 길을 찾고 실패를 위해 구실을 찾지 않는다는 말이 있습니다. Juniper인증 JN0-130시험이 영어로 출제되어 시험패스가 너무 어렵다 혹은 회사다니느라 공부할 시간이 없다는 등등은 모두 공부하기싫은 구실에 불과합니다. ITExamDump의 Juniper인증 JN0-130덤프만 마련하면 실패를 성공으로 바꿀수 있는 기적을 체험할수 있습니다.제일 간단한 방법으로 가장 어려운 문제를 해결해드리는것이ITExamDump의 취지입니다.
ITExamDump는 믿을 수 있는 사이트입니다. IT업계에서는 이미 많이 알려져 있습니다. 그리고 여러분에 신뢰를 드리기 위하여 Juniper 인증JN0-130 관련자료의 일부분 문제와 답 등 샘플을 무료로 다운받아 체험해볼 수 있게 제공합니다. 아주 만족할 것이라고 믿습니다. ITExamDump제품에 대하여 아주 자신이 있습니다. Juniper 인증JN0-130 도 여러분의 무용지물이 아닌 아주 중요한 자료가 되리라 믿습니다. 여러분께서는 아주 순조로이 시험을 패스하실 수 있을 것입니다.
JN0-130 덤프무료샘플다운로드하기: http://www.itexamdump.com/JN0-130.html
NO.1 Which two types of routes may be advertised via EBGP? (Choose two.)
A. Routes that do not originate in the local AS and are learned by OSPF.
B. Routes that originate on the local router and are advertised into OSPF.
C. Routes that are transiting the local router and are BGP learned routes.
D. Routes that originate on the local router and are injected using a route map.
Answer: CD
Juniper JN0-130덤프 JN0-130 pdf JN0-130
NO.2 In a Bridged 1483 network, which set of commands is used to configure an ATM subinterface?
A. interface atm 6/0.33
atm pvc 33 0 33 aal5snap
description Company-XYZ
encapsulation bridge1483
ip address unnumbered loopback0
B. interface atm 6/0.33
atm pvc 33 0 33 aal5snap
description Company-XYZ
encapsulation bridge1483
ip unnumbered loopback0
C. interface atm 6/0.33
atm pvc 33 0 33 aal5snap
encapsulation bridge1483
description Company-XYZ
ip address unnumbered loopback0
D. interface atm 6/0.33
atm pvc 33 0 33 aal5snap
encapsulation bridge1483
description Company-XYZ
ip unnumbered loopback0
Answer: D
Juniper덤프 JN0-130 pdf JN0-130 JN0-130 JN0-130 JN0-130
NO.3 Which CLI command disconnects all subscribers on an ATM PVC?
A. clear port 4/3.99
B. logout port 4/3.99
C. clear subscriber port 4/3.99
D. logout subscriber port 4/3.99
Answer: D
Juniper dumps JN0-130 JN0-130 JN0-130
NO.4 Which three statements about Label-Switched Paths (LSPs) are true? (Choose three.)
A. LSPs are bidirectional.
B. LSPs are unidirectional.
C. LSPs can be signaled by CAC.
D. LSPs can be configured explicitly.
E. LSPs can be configured dynamically.
Answer: BDE
Juniper기출문제 JN0-130자료 JN0-130자료 JN0-130자료
NO.5 Which CLI command displays the status of a PPP over Ethernet subinterface?
A. show pppoe interface
B. show ppp int state up
C. show ip interface brief
D. show pppoe subinterface
Answer: D
Juniper JN0-130 JN0-130 JN0-130 dumps
NO.6 Which message type is used to initiate an RSVP-TE label switched path?
A. path
B. resv
C. setup
D. session
Answer: A
Juniper최신덤프 JN0-130자료 JN0-130 JN0-130
NO.7 Is the IS-IS Designated Intermediate System (DIS) election process called Deterministic or Static and
why?
A. It is Static. If the priorities are equal for a new neighbor and the current DIS only.
B. It is Deterministic. If the well-known pseudonode and system ID is configured on the new neighbor only.
C. It is Deterministic. When a new router appears on a multi-access network with a higher priority value, it
is elected as the DIS.
D. It is Static. When a new intermediate system powers up on a multi-access network, even if it has a
higher priority, it may become a backup DIS.
Answer: C
Juniper JN0-130 JN0-130기출문제 JN0-130 dumps
NO.8 Which configuration command places interfaces whose IP addresses are between 192.168.0.0 and
192.168.255.255 into OSPF area 0?
A. network 192.168.0.0 255.255.0.0 area 0.0.0.0
B. network 192.168.0.0 0.0.255.255 area 0.0.0.0
C. area 0.0.0.0 network 192.168.0.0 255.255.0.0
D. area 0.0.0.0 network 192.168.0.0 0.0.255.255
Answer: B
Juniper JN0-130 JN0-130 JN0-130
NO.9 Which CLI command is used to set a Privileged Exec password of mypassword?
A. enable password 0 mypassword
B. enable password 3 mypassword
C. enable password 5 mypassword
D. enable password 10 mypassword
Answer: A
Juniper JN0-130 JN0-130 dump JN0-130 JN0-130 JN0-130
NO.10 You would like to view all Fast Ethernet interfaces currently using VLAN tagging and the specific VLANs
each interface is using.
Which CLI command displays this information?
A. show fast interface
B. show vlan interface
C. show vlan subinterface
D. show fast interface vlan
Answer: C
Juniper JN0-130 pdf JN0-130 JN0-130최신덤프 JN0-130
NO.11 Why would you make a non-backbone area a stub or not-so-stubby area?
A. to aggregate routes learned from the ABR
B. to lower the cost of routes advertised by the ABR
C. to connect a non-contiguous area to the backbone
D. to decrease the size of the link-state database in that area
Answer: D
Juniper최신덤프 JN0-130 JN0-130 dumps JN0-130최신덤프 JN0-130시험문제
NO.12 Which three statements are true regarding the DHCP Internal Server? (Choose three.)
A. Can be in remote-access mode.
B. Can be in equal-access mode.
C. Can be in standalone mode.
D. Standalone mode is the default.
E. Equal-access mode is the default.
Answer: BCE
Juniper JN0-130 JN0-130 JN0-130 JN0-130
NO.13 Which two services protect the ERX Edge Router from unauthorized CLI logins?
A. IPSec
B. SecureID
C. local passwords
D. default IP policy
E. RADIUS authentication
Answer: CE
Juniper JN0-130 JN0-130 JN0-130덤프 JN0-130자료
16. Your ERX Edge Router is constantly going to a boot## prompt.
What is the most likely cause for this condition?
A. bad SRP
B. low voltage
C. bad mid-plane
D. corrupted flash
Answer: D
Juniper JN0-130 JN0-130덤프
17. Which sequence of events describes the order used to restore normal router operation after
experiencing a corrupted flash?
A. initialize flash, reload, copy new system files from FTP server
B. reload, copy new system files from FTP server, initialize flash
C. initialize flash, copy new system files from FTP server, reload
D. reload, initialize flash, copy new system files from FTP server
Answer: C
Juniper시험문제 JN0-130 pdf JN0-130
18. You are trying to recover from a corrupted flash.
Which configuration command configures an IP address of 192.168.1.1/24 on the SRP management
interface when the ERX1400 router is at the boot## prompt?
A. ip address 192.168.1.1/24
B. ip address 192.168.1.1 subnetmask 24
C. ip address 192.168.1.1 255.255.255.0
D. ip address 192.168.1.1 mask 255.255.255.0
Answer: C
Juniper최신덤프 JN0-130 JN0-130기출문제 JN0-130
19. What describes the functionality of NTP when using multiple virtual routers?
A. All virtual routers can act as NTP clients and servers.
B. Only one virtual router can act as an NTP client and a server.
C. Only one virtual router can act as an NTP server but all can be clients.
D. Only one virtual router can act as an NTP client but all can be servers.
Answer: D
Juniper최신덤프 JN0-130 JN0-130
20. Which configuration command is used to make the ERX Edge Router an NTP server?
A. set ntp-server
B. set ntp server
C. ntp-server enable
D. ntp server enable
Answer: D
Juniper JN0-130최신덤프 JN0-130자격증 JN0-130 JN0-130 JN0-130
21. Which configuration command allows a virtual router to receive updates from a configured NTP
source?
A. ntp enable
B. enable ntp
C. set ntp-client
D. enable ntp-client
Answer: A
Juniper JN0-130 JN0-130 JN0-130기출문제 JN0-130 pdf
22. Which configuration command is used to send debug level events to the console in real time?
A. log here severity debug
B. log destination console severity debug
C. log severity debug destination console
D. log realtime destination console severity debug
Answer: B
Juniper덤프 JN0-130 JN0-130 dumps
23. Which command initiates a packet trace for all PPP packets on interface atm 6/1.33 ?
A. log filter debug pppPacket atm 6/1.33
B. log severity debug pppPacket atm 6/1.33
C. log filter debug category pppPacket atm 6/1.33
D. log severity debug category pppPacket atm 6/1.33
Answer: B
Juniper JN0-130 JN0-130
24. Log messages are appearing very quickly on the console of your ERX Edge Router.
Which Privileged Exec command disables real-time console logging?
A. no log here
B. no log console
C. destination console severity 7
D. destination console logging off
Answer: A
Juniper JN0-130자료 JN0-130
25. Which two configuration commands are required to direct debug level console logging to your current
ERX Edge Router Telnet session? (Choose two.)
A. log here
B. log telnet here
C. log destination console severity 7
D. log destination telnet severity debug
Answer: AC
Juniper JN0-130덤프 JN0-130기출문제 JN0-130 JN0-130덤프
26. A log filter of log severity DEBUG pppPacket ATM 4/3.66 is configured within the category of
pppPacket.
Which configuration command removes this specific log filter?
A. no log severity pppPacket
B. no log severity debug pppPacket
C. no log severity pppPacket atm 4/3.66
D. no log severity debug pppPacket 4/3.66
Answer: C
Juniper자격증 JN0-130 JN0-130인증 JN0-130자격증 JN0-130 dump
27. Which configuration command removes all log filters currently configured on the ERX Edge Router?
A. no log here
B. no log fields
C. no log filters
D. no log severity
Answer: C
Juniper덤프 JN0-130 dumps JN0-130 JN0-130인증 JN0-130시험문제
28. Which three statements describe macros on the ERX Edge Router? (Choose three.)
A. They prompt users for input.
B. They cannot prompt users for input.
C. They can be created on the router itself.
D. They are an embedded programming language.
E. They can be created on the user's workstation.
Answer: ADE
Juniper JN0-130최신덤프 JN0-130 dumps JN0-130
29. Which command is used to execute a macro called setup.mac ?
A. macro setup
B. macro setup.mac
C. run macro setup
D. run macro setup.mac
Answer: B
Juniper JN0-130 JN0-130기출문제 JN0-130 JN0-130자격증
30. Which control expression must be the last line in all macros?
A. <# end #>
B. <# finish #>
C. <# endtmpl #>
D. <# terminate #>
Answer: C
Juniper JN0-130 JN0-130기출문제 JN0-130
NO.14 Which two BGP attributes are incorporated for loop prevention within an AS using a route reflection
configuration? (Choose two.)
A. AS Path
B. Next Hop
C. Cluster List
D. Originator ID
Answer: CD
Juniper JN0-130 dumps JN0-130 JN0-130 JN0-130 pdf JN0-130시험문제
NO.15 Which CLI command displays the VRFs that are operational within each virtual router?
A. show vir
B. show ip vrf
C. show vrf vir
D. show mpls vrf
Answer: A
Juniper JN0-130기출문제 JN0-130 JN0-130자료
ITexamdump의 EN0-001덤프의 VCE테스트프로그램과 642-385덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 850-001시험에 대비한 고품질 덤프와 C_TBIT44_73시험 최신버전덤프를 제공해드립니다. 최고품질 JK0-U31시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기